10/30/2022 0 Comments Twisted pair cable in hindi![]() ![]() These two types of connectors are fairly similar and are made of plastic with thin metal pins. The RJ simply stands for Registered Jack while the numbers 11 and 45 relate to a number of the interface standard. If the connector didn't crimp properly, cut off the connector and redo it.Twisted pair cable is the most commonly used type of cable within today’s structured network cabling systems and the two main types of connectors associated with this network cabling are the RJ-11 and RJ-45 connectors. Now the installation is done.Īfter the whole installation, you should check to ensure all conductors are making contact and that all pins have been crimped into their respective conductors. Do this carefully, as it's the last step before crimping on the connector.Ĭarefully insert the connector and cable into the crimping tool, which has two dies that will press into the connector, and push the pins in the connector into the conductors inside the connector. If they don't line up, pull them out and line up. Insert the conductors in the connector, ensuring that all conductors line up porperly with the pins as they were in the previous step. Second, the total length of exposed connectors after trimming should be no longer than 0.5" to 0.625". First, trim the conductors so that the ends are even with each other, making sure that the jacket of the cable will be inside the connector. TWISTED PAIR CABLE IN HINDI CODELine up the individual condutors so that the color code matches the color-coding standard you are using. Untwist all the inner conductor pairs and spread them apart so that you can see each individual conductor. If a jacket slitting cord (usually a white thread) is present, separate it from the conductors and trim it back to the edge of the jacket. Remove the stripper from the cable and pull the trimmed jacket from the cable, exposing the inner conductors. Then, rotate the stripper around the cable twice. Use the cable stripper to strip about 1.5" of the jacket from the end of the cable. Measure the cable you want to put ends on and trim it to the proper length using the cable cutter. Check the manufacturer's instructions before installing any connector. Equipment from some manufacturers may require you to perform warning slightly different steps. Pay particular attention to the order of these steps and be sure to follow them exactly. Now we will go over the steps for installing the connectors. It may have everything you need to get started. Tips: Normally, the above-mentioned tools come as a network installation tool kit to meet multiple needs. This device tests for a continuous signal from the source connector to the destination and also tests the quality of that connection. ![]() The last tool you are going to use is a cable tester. So, make sure you choose the right crimping tool. Some crimpers can finish both RJ45 and RJ11 connectors. But there are specific types of crimpers used for specific cables. A cable crimper is used to finish the connection between network cables and connectors. Many different kinds of cable strippers exist, but the most common are the small, plastic ones that easily fit into a shirt pocket. It will only cut through the outer jacket of the cable, not through the conductors inside. The first tool is a cable-jacket stripper. There are mainly three tools which are needed in the coming installation. Tools for Installation of Twisted Pair Cable Connectors It is not recommended to use RJ11 plugs for RJ45 jacks as it may cause damages on the devices. Notice: Due to the different structure of RJ45 and RJ11 connectors, the wiring sequence standard and applications are also different. It is an indispensable supporting role in Ethernet and is generally used at both ends of a network cable to connect various network devices, such as computers, routers, switches, etc. An RJ45 connector is usually used for data transmission in scenarios such as monitoring projects and general cabling in the equipment room. Therefore, RJ45 connectors are larger than RJ11 connectors in forms. RJ45 connectors normally have 8 positions and 8 contacts. They are not internationally standardized, but used to be a very popular choice for both commercial and residential telephone applications due to their simplicity and small forms. RJ11 connectors typically have only 6 positions and 4 or 2 contacts. There are mainly two types of cable connectors used for twisted pair connection in voice and data communication installation. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |